Email me newest jobs similar to this one
17 days ago
only 11 days until close

Aircraft Structures Mechanic B


Boeing
Location: Everett, Washington
Job type: Permanent
Sector: Maintenance
Category: Mechanic
Apply
Select how you want to share:
View similar
Mechanics in this position assemble precision and structural aircraft components and sub-assemblies. These sub-assemblies are later incorporated in larger assemblies that are subsequently installed on the airplane. Employment in this position also requires lifting and pushing/pulling up to 35 pounds, rotation of head/neck, bending and twisting at the waist, walking, standing, kneeling, reaching, sitting, climbing/balancing, use of high and low impact vibratory tools, flexion/extension, contact with metals, lubricants, solvents and plastics, exposure to noise, and the use of personal safety gear for face, eyes, hand/arm and ears. Additional Tasks, Duties and Responsibilities: Locate work area using drawings which specifies airplane number, section number, and three-point location. Obtain and verify kitted (pre-picked) detail parts, standards, and assemblies were issued correctly. Ensure that parts issued are effective for the airplane and are free of visible defects. If parts are not pre-picked, get parts and ensure that parts selected are effective for the airplane and are free of visible defects. Set up assembly tools per tooling instructions or drawing. Review bar chart or automated time line to determine which job to work on and obtain appropriate drawings for job. Operate mechanical lifts of various types (e.g. tiger and snorkel lifts), as required, to locate parts/assemblies into position or to perform assembly work. Locate tools and/or parts on airplane using tooling holes, pilot holes, K holes, or by hand (as required), per drawing or tooling instructions. Align parts and secure in place using Clecos or tooling/hand clamps. Check for good edge margins and alignment. Shim and/or trim parts as required. Select drill bits, reamers and/or countersinking tools for pilot and full size holes. Locate, drill pilot holes using drill motor and proper size drill bit(s). Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor. Set countersinking tools to proper depth as required. Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners. Use solvents to clean surfaces prior to sealing or assembly. Apply sealant, alodine, primer, adhesives and special finishes. Load and unload ovens to bond detail parts to assemblies. Apply permanent or temporary part mark and protective material to assemblies for preparation of shipment. Handle and dispose of hazardous materials in approved manner. Determine and obtain correct type and size fasteners. Cold work holes to prepare for close tolerance fastener installation. Install bushings into housings using arbor press and/or hydraulic puller. Apply liquid nitrogen to facilitate installation of bushings. Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner). Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing. Boeing is the world's largest aerospace company and leading manufacturer of commercial airplanes and defense, space and security systems. We are engineers and technicians. Skilled scientists and thinkers. Bold innovators and dreamers. Join us, and you can build something better for yourself, for our customers and for the world.

Division

777 Program

Relocation Assistance Available

No. Relocation assistance is not a negotiable benefit.

Qualifications

Current Boeing employees working in Puget Sound and Portland must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool

Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

This is an hourly position governed by the IAM Collective Bargaining agreement.

High school graduate or GED preferred.

"This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. "US Person" includes US Citizen, lawful permanent resident, refugee, or asylee."

Experience using a computer such as internet navigation, email, Microsoft Office and/or other specialized computer applications

Experience reading and interpreting assembly instructions or drawings

Experience Level

Individual Contributor

Job Type

Standard

Travel

No

Contingent Upon Program Award

No

Union

Yes

Job Code

30005

Apply
Mechanics in this position assemble precision and structural aircraft components and sub-assemblies. These sub-assemblies are later incorporated in larger assemblies that are subsequently installed on the airplane. Employment in this position also requires lifting and pushing/pulling up to 35 pounds, rotation of head/neck, bending and twisting at the waist, walking, standing, kneeling, reaching, sitting, climbing/balancing, use of high and low impact vibratory tools, flexion/extension, contact with metals, lubricants, solvents and plastics, exposure to noise, and the use of personal safety gear for face, eyes, hand/arm and ears. Additional Tasks, Duties and Responsibilities: Locate work area using drawings which specifies airplane number, section number, and three-point location. Obtain and verify kitted (pre-picked) detail parts, standards, and assemblies were issued correctly. Ensure that parts issued are effective for the airplane and are free of visible defects. If parts are not pre-picked, get parts and ensure that parts selected are effective for the airplane and are free of visible defects. Set up assembly tools per tooling instructions or drawing. Review bar chart or automated time line to determine which job to work on and obtain appropriate drawings for job. Operate mechanical lifts of various types (e.g. tiger and snorkel lifts), as required, to locate parts/assemblies into position or to perform assembly work. Locate tools and/or parts on airplane using tooling holes, pilot holes, K holes, or by hand (as required), per drawing or tooling instructions. Align parts and secure in place using Clecos or tooling/hand clamps. Check for good edge margins and alignment. Shim and/or trim parts as required. Select drill bits, reamers and/or countersinking tools for pilot and full size holes. Locate, drill pilot holes using drill motor and proper size drill bit(s). Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor. Set countersinking tools to proper depth as required. Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners. Use solvents to clean surfaces prior to sealing or assembly. Apply sealant, alodine, primer, adhesives and special finishes. Load and unload ovens to bond detail parts to assemblies. Apply permanent or temporary part mark and protective material to assemblies for preparation of shipment. Handle and dispose of hazardous materials in approved manner. Determine and obtain correct type and size fasteners. Cold work holes to prepare for close tolerance fastener installation. Install bushings into housings using arbor press and/or hydraulic puller. Apply liquid nitrogen to facilitate installation of bushings. Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner). Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing. Boeing is the world's largest aerospace company and leading manufacturer of commercial airplanes and defense, space and security systems. We are engineers and technicians. Skilled scientists and thinkers. Bold innovators and dreamers. Join us, and you can build something better for yourself, for our customers and for the world.

Division

777 Program

Relocation Assistance Available

No. Relocation assistance is not a negotiable benefit.

Qualifications

Current Boeing employees working in Puget Sound and Portland must submit an Employee Request Transfer (ERT) to be considered in the eligible candidate pool

Resumes of current Puget Sound Boeing employees submitted via Careers at Boeing will not be considered.

This is an hourly position governed by the IAM Collective Bargaining agreement.

High school graduate or GED preferred.

"This position must meet Export Control compliance requirements, therefore a “US Person” as defined by 22 C.F.R. § 120.15 is required. "US Person" includes US Citizen, lawful permanent resident, refugee, or asylee."

Experience using a computer such as internet navigation, email, Microsoft Office and/or other specialized computer applications

Experience reading and interpreting assembly instructions or drawings

Experience Level

Individual Contributor

Job Type

Standard

Travel

No

Contingent Upon Program Award

No

Union

Yes

Job Code

30005

Apply
Apply

Email me newest jobs similar to this one

  Back to the top